A FIPS 140-2 cryptographic module shall implement at least one Approved security function used in an Approved mode of operation. For an algorithm to be listed on a validation certificate as FIPS Approved, the algorithm implementation must meet all the requirements of FIPS 140-2 and must have received an algorithm validation certificate.
Jul 12, 2017 · FIPS stands for “Federal Information Processing Standards.” It’s a set of government standards that define how certain things are used in the government–for example, encryption algorithms. FIPS defines certain specific encryption methods that can be used, as well as methods for generating encryption keys. FIPS 140-3 is being devised by NIST now for adoption in the future.) Users who are subject to the FIPS regulations must ensure that they have Mozilla's FIPS Mode enabled when they use Mozilla software, in order to be fully conformant. Instructions for how to configure Firefox into FIPS mode may be found on support.mozilla.com. Furthermore, we recommend you remove all non-FIPS ciphers from the list to ensure the connection failure doesn't occur. In ASDM, go to Configuration > Remote Access VPN > Advanced > SSL Settings to specify the SSL encryption types. In the Encryption area, move a FIPS-compliant cipher to the top position in the list. The vendor will say "Our FIPS- enabled XYZ product uses a PQR product, which is FIPS validated," but you have to read the fine print. Why is this important? It's better to have FIPS validated product than to have a Frankenstein's monster of some FIPS validated and some not FIPS validated software. The security weakness is in the gaps. Caveat cryptographic algorithms used in some SSL cipher suites are not FIPS-approved, and therefore are not allowed for use in SSL VPNs that are to be used in applications that must conform to FIPS 140-2. This means that to be run in FIPS-compliant mode, an SSL VPN gateway must only allow cipher suites that are allowed by FIPS 140-2. Re: FIPS Compliant site-to-site VPN Asa5505 can suport up to 25 ipsec tunnels so the answer to your question is yes, you can have more than one L2L vpn from asa_f1 , see examples in bellow link under site-to-site VPN. The FIPS-compliant Cisco VPN client is available in a separate FIPS-compliant release. FIPS-compliance for the AnyConnect VPN client is a feature enabled in the local policy, and does not require a different release of the AnyConnect client.
There is a patch lingering in Red Hat Bugzilla #1369260 which adds FIPS support to OpenVPN.. This is an interesting feature for many who need to apply policies where FIPS is a hard requirement.
Use FIPS-approved encryption and authentication algorithms when creating VPN tunnels. The SonicWall UTM appliance supports the following FIPS-approved cryptographic algorithms: AES (128, 192, and 256-bit) in CBC mode (Cert. #1200) The VPN solution uses a pair of encrypted Ethernet bridges to provide a secure Ethernet tunnel between the dispatch center and a remote MIP 5000 console. The secure Ethernet tunnel supports a remote console operator receiving audio from and transmitting audio to radio channels and other MIP 5000 consoles using AES encryption. Apr 21, 2009 · FIPS compliance We are looking to replace our 110c and also address some audit items. We need to install a FIPS compliant firewall with FIPS 140-2 compliant SSL VPN. We are looking at the 200D for the hardware, but I'm confused about the firmware. The only certified firmware that I see on the NIST site is 5.0.10.
AES, FIPS 197, NIST Certificate #5 DSA, FIPS 186-2, NIST Certificate #70 FIPS compliance can be achieved with Sterling Connect:Direct only by installing Sterling Connect:Direct Secure Plus and enabling FIPS mode on the supported platforms.
software VPN Client meets the security requirements of FIPS 140-2, and how to run the VPN Client in secure FIPS 140-2 mode. This policy was prepared as part of the Level 1 FIPS 140-2 validation of the VPN Client. The Cisco Software VPN Client is referred to in this document as the VPN Client, the software client, and the module. FIPS 140-2 Jul 12, 2017 · FIPS stands for “Federal Information Processing Standards.” It’s a set of government standards that define how certain things are used in the government–for example, encryption algorithms. FIPS defines certain specific encryption methods that can be used, as well as methods for generating encryption keys. FIPS 140-3 is being devised by NIST now for adoption in the future.) Users who are subject to the FIPS regulations must ensure that they have Mozilla's FIPS Mode enabled when they use Mozilla software, in order to be fully conformant. Instructions for how to configure Firefox into FIPS mode may be found on support.mozilla.com. Furthermore, we recommend you remove all non-FIPS ciphers from the list to ensure the connection failure doesn't occur. In ASDM, go to Configuration > Remote Access VPN > Advanced > SSL Settings to specify the SSL encryption types. In the Encryption area, move a FIPS-compliant cipher to the top position in the list. The vendor will say "Our FIPS- enabled XYZ product uses a PQR product, which is FIPS validated," but you have to read the fine print. Why is this important? It's better to have FIPS validated product than to have a Frankenstein's monster of some FIPS validated and some not FIPS validated software. The security weakness is in the gaps. Caveat cryptographic algorithms used in some SSL cipher suites are not FIPS-approved, and therefore are not allowed for use in SSL VPNs that are to be used in applications that must conform to FIPS 140-2. This means that to be run in FIPS-compliant mode, an SSL VPN gateway must only allow cipher suites that are allowed by FIPS 140-2. Re: FIPS Compliant site-to-site VPN Asa5505 can suport up to 25 ipsec tunnels so the answer to your question is yes, you can have more than one L2L vpn from asa_f1 , see examples in bellow link under site-to-site VPN.